Cataloghi

Red and black tinned wires with a 2-pin JST PH connector on the end. 4" / 100mm long. Matches up nicely with our Lipoly chargers!We have the socket...

Piezo buzzers are used for making beeps, tones and alerts. This one is petite but loud! Drive it with 3-30V peak-to-peak square wave. To use, conne...

Most projects these days have multiple power supplies: say a battery or DC wall plug or USB for multiple powering options. Juggling these to have s...

One of our star Feathers is the Adafruit HUZZAH32 ESP32 Feather - with the fabulous ESP32 WROOM module on there, it makes quick work of WiFi and Bl...

As we've been adding  STEMMA QT connectors to our breakouts and dev boards, folks have been really enjoying the simplicity and speed of plugging in...

Micro SD cards and microcontrollers go together like micro-peanutbutter-and-jelly: SD cards are inexpensive, durable, easy to find at any shop, com...

The TLV493D 3-axis magnetometer is a great little sensor for detecting magnets in 3D. In fact, the manufacturer Infineon suggests it could be used ...

PowerBoost 1000C is the perfect power supply for your portable project! With a built-in load-sharing battery charger circuit, you'll be able to kee...

This super small mono amplifier is surprisingly powerful - able to deliver up to 2.5 Watts into 4-8 ohm impedance speakers. Inside the miniature ch...

Virtual reality is in, but you shouldn\'t have to drop hundreds of dollars to gain access to the technology behind it. Luckily, that\'s where the S...

The SparkFun BMI270 6DoF IMU Breakout is a Qwiic-enabled breakout board based on the ultra-low power BMI270 from Bosch. This chip is a highly integ...

The TFMini-S Micro LiDAR Module is a ToF (Time of Flight) LiDAR sensor capable of measuring the distance to an object as close as 10 centimeters (+...

The SparkFun Triad Spectroscopy Sensor is a powerful optical inspection sensor also known as a *spectrophotometer*. Three AS7265x spectral sensors ...

This is a 10 pack of Biomedical Sensor Pads, disposable electrodes that can be used to measure EEG, ECG and EMG levels. these little pads are perfe...

This is a force sensitive resistor with a round, 0.5\" diameter, sensing area. This FSR will vary its resistance depending on how much pressure is ...

This is a simple, but very powerful stepper motor with a 4-wire cable attached. This is a [Bipolar](http://en.wikipedia.org/wiki/Bipolar_electric...

These headers are made to work with the Teensy 4.1, Teensy 3.6, and Teensy 3.5 development boards. Each set of headers allows for your Teensy to be...

These headers are made to work with the Teensy 4.0, Teensy 3.2, and Teensy LC development boards. Each kit of headers makes your Teensy breadboard ...

These are 6\" long jumper wires terminated as male to female. Use these to jumper from any male or female header on any board. Multiple jumpers can...

This DC power jack/connector is just like the other one that we carry except that it\'s terminated with breadboard-friendly pins instead of wide so...

If you want to get some sound out of your project but have a tight space budget, this is a good way to do it. This 2.5W, 4 Ohm speaker is only 28mm...

This is a 50mm long ESLOV to ESLOV cable. The ESLOV connector has five pins (one more than standard I2C) for automatically configuring the module a...

The MyoWare® 2.0 Reference Cable is meant as an extension for the [MyoWare 2.0 Muscle Sensor\'s](https://www.sparkfun.com/products/18977) reference...

The SparkFun ESLOV to Qwiic Bridge lets you quickly and easily connect Qwiic breakouts to Arduino boards with an ESLOV connector for I2C communicat...