Motori

  This gearmotor is a miniature (0.94" x 0.39" x 0.47"), high-quality, low-current motor with 10:1 metal gearbox, similar to Sanyo’s popular 12 mm ...

  This gearmotor is a miniature (0.94" x 0.39" x 0.47"), high-quality, high-power motor with 30:1 metal gearbox, similar to Sanyo’s popular 12 mm g...

  This gearmotor is a miniature (0.94" x 0.39" x 0.47"), high-quality, high-power motor with 50:1 metal gearbox, similar to Sanyo’s popular 12 mm g...

  This gearmotor is a miniature (0.94" x 0.39" x 0.47"), high-quality, low-current motor with 100:1 metal gearbox, similar to Sanyo’s popular 12 mm...

  The TReX blends RC, analog, and serial inputs for a powerful motor control solution capable of delivering a continuous 13 A per motor. The TReX w...

  This lower-power, smaller, and lower-cost version of the TReX is the ultimate general-purpose motor controller for small motors: it has a wide op...

Watch out, here it comes! Our new high voltage, coreless HS-7245MH servo delivers exceptional speed and torque in a compact package. Built with an ...

New Premium HSR-5990TG is the replacement of current HSR-5995TG. With accumulated know-how from Robot technology, HSR-5990TG shows more stable perf...

When high-power motor stalls or stops suddenly, it can generate a high-voltage surge that can damage the circuitry of the motor controller and burn...

The new generation of motor controllers from Phidgets Inc. are able to rapidly change motor directions, strongly brake the motor, and produce power...

Get moving with this powerful Bipolar Stepper Phidget. With a maximum power supply of 30V, it can provide up to 8A of current to each stepper coil....

The DCC1002 gives you complete control of one medium to large DC motor from one of the ports on your VINT hub. You can control motor velocity, acce...

This is a DC sucker type electromagnet with 8kg holding force and 1.5W power. It should be operated at 5V. The magnetic poles of the electromagnet ...

This is a DC sucker type electromagnet with 35kg holding force and 3W power. It should be operated at 5V. The magnetic poles of the electromagnet c...

    Servo Channels - up to 84 Logic Outputs - up to 84 Logic Inputs - up to 84 10-bit Analogue Inputs - up to 36 Servo Refresh...

MCU : ST CORTEX-M3 ( STM32F103C8 @ 72MHZ,32BIT) POSITION SENSOR : Contactless absolute encoder (12BIT,360 DEGREE) Maker : ams (www.ams.com), P...

For RX64 Dynamixel Servos. Includes: - Thrust Horn : 1 pc - Wrench Bolt (M3*8) : 1 pc Thrust bearing and washers not in...

SPECIFICATIONS - This part is assembled on to the final wheel gear and is used to connect with other frames for the RX-64 - The center has been ...

Bracket for RX64 Dynamixel Servos, 4 screw and 4 nuts included.   More informations about the Dynamixel System ->

Includes: - Horn Idle : 1 pc Only the Horn idle included     More informations about the Dynamixel System ->  

Includes: - Horn Idle : 1 pc - MF106ZZ Bearing : 1 pc - Cap Bearing : 1 pc - Wrench Bolt (M2.5*8) : 1 pc - Wrench Bolt (M2*3) : 6 pcs ...

This shield makes it easy to control two high-power DC motors with your Arduino or Arduino-compatible board. Its twin discrete MOSFET H-bridges sup...