Sparkfun

TRRS connectors are the audio-style connectors that you see on some phones, MP3 players and development boards. TRRS stands for \"Tip, Ring, Ring, ...

These are the sturdy little stomp switches that you find on guitar effects pedals. They’re 3PDT (three-pole, double-throw) type switches. These swi...

Are you looking to add a lot of color to your project? These massive 32x32 RGB LED panels are an awesome place to start. You can create animations,...

The SN74HC595N is a simple 8-bit shift register IC. Simply put, this shift register is a device that allows additional inputs or outputs to be adde...

A simple slide potentiometer can go a long way. Rated at 10KOhm and 0.1W. Comes with solder tab connections. The pot has an overall travel of 30mm ...

These DC powered heating pads are perfect for near-body heating applications. They get warm to the touch but not too hot as long as you provide the...

Ever hear of a thing called RGB? Red, Green, Blue? How about an RGB LED? These 5mm units have four pins: one for each color and a common anode. Use...

PICAXE-08M2 microcontroller chip. PICAXE is a neat entry-level microcontroller system that is relatively cheap to get started with. The chip is...

This plastic knob accepts a 6mm shaft and has a 15mm outer diameter. They simple press-fit onto a shaft. These are clear so that they can be used w...

These 10 segment bar graph LEDs have many uses. With a compact footprint, simple hookup, they are easy for prototyping or finished products. Essent...

This is a translucent silicon rubber button pad with 4 buttons orignally inspired by the folks at [monome.org](http://monome.org). Each button has ...

These are very common, high quality BJT NPN transistors made by ST Micro. **Documents:** * [Datasheet](http://www.sparkfun.com/datasheets/Compone...

This is a handy cable for connecting a six pin GHR-06V type locking connector to breadboard friendly male pins. The cable features a 1.25mm pitch G...

This is a basic RP-SMA (Reverse Polarity Sub-Miniature A) male to female connector cable. Each cable is 10M (393.7in.) long with RG58 housing. The ...

You\'ve got the wrong USB cable. It doesn\'t matter which one you have, it\'s the wrong one. But what if you could have the right one? What if you ...

This panel mount USB-C extension cable enables you to more easily enclose a project that contains a USB-C port. The cable is 6\" in length and incl...

This is a very simple 1m long Male RP-TNC to Male RP-SMA cable. We like to use this cable to connect our ultra high-frequency RFID antennas to an e...

This is a 4 pack of wires that are pre-terminated with an alligator clip on one end and a hookup pigtail on the other. Alligator clips are a staple...

This is an interface cable for the [Bus Pirate](http://www.sparkfun.com/commerce/product_info.php?products_id=9544), designed to connect to its 2x5...

The SparkFun Analog MEMS Microphone Breakout makes it easy to work with the SPH8878LR5H-1 analog microphone from Knowles. This board features an Op...

The SparkFun Analog MEMS Microphone Breakout makes it easy to work with the InvenSense ICS-40180 analog microphone. This board features an OpAmp to...

This simple board breaks out a female USB type A connector\'s VCC, GND, D- and D+ pins to a 0.1\" pitch header. If you want to add a USB to your p...

This is a clever little breakout board for both the RGB and R/G illuminated rotary encoders. On one side, it breaks out all of the RGB pins to stan...

This breakout for the Silicon Laboratories Si4703 FM tuner chip is a little more stripped down than our FM Tuner Evaluation Board. If your project ...