SKU DRI0009/B
2x2A DC Motor Shield for Arduino
Prezzo originale
€20,35
-
Prezzo originale
€20,35
Prezzo originale
€20,35
€20,35
-
€20,35
Prezzo attuale
€20,35
Tutti i prezzi sono IVA inclusa
Disponibilità:
in magazzino
Disponibilità:
Esaurito
Disponibilità:
Da Ordinare
Arduino product family is a great learning platform for electronics, programming and robotics. But most projects at some point require mobility. This Arduino motor shield allows for motor control with Arduino right away. Stack up this shield on your controller and drive 2 DC motors with higher power requirements. Depending on the motor of choice, you can make it fast or handle a higher payload. This Arduino Motor Shield (2A) uses L298P chip which allow to drive two 7-12V DC motors with maximum 2A current. This arduino motor shield can be directly mounted onto standard Arduino Uno and Arduino Mega.
Speed control is achieved through conventional PWM which can be obtained from Arduino’s PWM output Pin 5 and 6. The enable/disable function of the motor control is signaled by Arduino Digital Pin 4 and 7. The Motor shield can be powered directly from Arduino or from external power source. It is strongly encouraged to use external power supply to power the motor shield.
This arduino motor shield is ideal for building Arduino robot or other Arduino motor control projects.
There is another version of 2x2A motor shield (Twin) which uses different pins to avoid conflicting pin allocation.
Compatibility
Compatibility
|
|
|
|
|
| Product Name |
2x1A DC Motor Shield for Arduino |
Micro:bit Driver Expansion Board |
Gravity: Dual Bipolar Stepper Motor Shield for Arduino (DRV8825) |
Quad DC Motor Driver Shield for Arduino |
| SKU |
DRI0001 |
DFR0548 |
DRI0023 |
DRI0039 |
|
Chip |
L293B |
HR8833 |
DRV8825 |
TB6612FNG |
|
Operating voltage |
5V DC | / | 3.3V/5V |
2.7~5.5V |
| Motor drive voltage |
7-12V DC |
3.5~5.5V DC |
8.2-45VDC |
2.5V-13.5V |
|
Maximum drive current |
1A each way | 1.5A | 1.6A |
1.2A continuous current (per channel) 2A (continuous pulse) 3.2A (single pulse) |
|
Motor drive using pins |
PIN4/5/6/7 (Arduino Controllor) |
/ |
D4，D5，D6 D7，D8，D12 |
D3,4,5,6,7,8,11,12 |
|
Dimension |
56x57mm |
63 x 58mm |
83*55*25mm |
52mm * 53mm |
|
Weight (g) |
60 | 64 | 48 | 24 |
|
Frequently used With |
FIT0278/FIT0503 |
|||
|
Key Features |
With motor indicator |
8-way servo interface DC motor x4/stepper motor x2(multiplexed with motor interface) |
Full step, 1/2, 1/4, 1/8, 1/16, 1/32 step mode |
High-speed drive capability, can drive ordinary 2-phase stepper motor to 5000RPM, and drive quad DC at the same time |
|
|
|
|
|
| Product Name |
Gravity: IO Expansion & Motor Driver Shield |
Gravity: 2x2A Motor Shield for Arduino Twin |
TMC260 Stepper Motor Driver Shield |
2x2A DC Motor Shield for Arduino |
| SKU |
DFR0502 |
DRI0017 |
DRI0035 |
DRI0009 |
|
Chip |
TB6612FNG |
L298 |
TMC260 |
L298P |
|
Operating voltage |
2.7~5.5V |
5V |
5V |
5V |
| Motor drive voltage |
12V (peak value) |
4.8 ～ 35V |
40V max |
6.5~12v(VIN Power Supply),4.8~35V (External Power Source) |
|
Maximum drive current |
1.2A continuous current (per channel) 2A (continuous pulse) 3.2A (single pulse) |
up to 2A/channel |
up to 2A per motor coil |
2A |
|
Motor drive using pins |
D4 D5 D6 D7 |
D10,11,12,13 |
/ |
Pin 4,5,6,7 are used to drive two DC motor |
|
Dimension |
68.5mm×53.3mm |
56x57mm |
55x55mm |
|
|
Weight (g) |
36 | 35 | 35 | 60 |
|
Frequently used With |
FIT0278/FIT0503 |
|||
|
Key Features |
Integrated XBee Slot, XBee, WiFi Bee, Bluetooth Bee, I2C. |
Mirrored version of DRI0009. Drive pins: 10, 11, 12, 13 Not compatible with IO expansion board V7.1. The control port is four, which reduces the overhead of the Arduino digital ports, and easy to program. |
Suitable for driving bipolar stepper motors. SPI serial bus control or STEP/DIR signal control. Controllers such as Mega with full port expansion. 256 times microstep subdivision. |
Use mirror motor to drive DRI0017 to aviod the conflicts . Support PWM speed control. Support PLL advance speed control |