Sparkfun

This is a translucent silicon rubber button pad with 4 buttons orignally inspired by the folks at [monome.org](http://monome.org). Each button has ...

This is a black plastic bezel, custom made to mate with the silicon rubber pads. Black 1/8" ABS plastic. Using two of these bezels with two of the ...

This is a black plastic bezel, custom made to mate with the silicon rubber pads. Black 1/8\" ABS plastic. Using two of these bezels with two of the...

This is a black plastic bezel, custom made to mate with the silicon rubber pads. Black 1/8" ABS plastic. We use four 4/40-0.5" size screws matched ...

This is a black plastic bezel, custom made to mate with the silicon rubber pads. Black 1/8\" ABS plastic. We use four 4/40-0.5\" size screws matche...

This a simple breakout board for the button pads. Each LED and button is brought out to the side connectors. The connectors are soldered to the bac...

This a simple breakout PCB for our [4x4 silicone button pads](https://www.sparkfun.com/products/7835). Each LED and button can brought out to the s...

This is a translucent silicon rubber button pad with 16 buttons originally inspired by the folks at monome.org. Each button has a hole underneath t...

This is a translucent silicon rubber button pad with 16 buttons originally inspired by the folks at [monome.org](http://monome.org). Each button ha...

No, this isn\'t a tank tread, this is a 0.5m long Cable Carrier with 10x15mm bits composing its main body and two screw fasteners at each end for e...

The CAN-BUS Shield provides your Arduino or Redboard with CAN-BUS capabilities and allows you to hack your vehicle. This shield allows you to poll ...

The CAN-BUS Shield provides your Arduino or Redboard with CAN-BUS capabilities and allows you to hack your vehicle. This shield allows you to poll ...

Fingerprint scanners have been easily available at a consumer level for a number of years now, so it is only logical that they would continue to gr...

Panasonic FK SMT Aluminum Electrolytic Capacitors feature a high endurance of up to 2000 hours at +105°C and a temperature range as low as -55°C. T...

This is a very common 0.1uF capacitor. Used on all sorts of applications to decouple ICs from power supplies. 0.1\" spaced leads make this a perfec...

This is a very common 22pF capacitor. Used with crystals for loading purposes. 0.1\" spaced leads make this a perfect candidate for breadboarding a...

Keep the outdoors out of your project! This is the threaded sealing cap that fits onto the Weatherproof Panel Mount USB-B connectors. The cap maint...

This board allows you to interface with your car's OBD-II bus. It provides you a serial interface using the ELM327 command set and supports all maj...

  This is a simple-to-use Carbon Monoxide (CO)sensor, suitable for sensing CO concentrations in the air. The MQ-7 can detect CO concentrations anyw...

This is a simple-to-use [Carbon Monoxide (CO)](http://en.wikipedia.org/wiki/Carbon_monoxide) sensor, suitable for sensing CO concentrations in the ...

This 3ft Category 6 (CAT 6) Ethernet cable is the solution to your internet working needs. With a speed of up to 500MHz you can connect to your LAN...

This is a USB 2.0 type A to Mini-B 5-pin cable. You know, the mini-B connector that usually comes with USB Hubs, Cameras, MP3 players, etc. You can...

This is a breakout board for the CC3000 WiFi Module. The CC3000 from TI (Texas Instruments) is a self-contained wireless network processor that mak...

This is a shield for the CC3000 WiFi Module. The CC3000 from TI (Texas Instruments) is a self-contained wireless network processor that makes incor...