sparkfun

The MyoWare® 2.0 Link Shield is designed to easily connect a [MyoWare 2.0 Muscle Sensor](https://www.sparkfun.com/products/18429) to your Arduino m...

Using our muscles to control things is the way that most of us are accustomed to doing it. We push buttons, pull levers, move joysticks... but what...

The MyoWare® 2.0 Muscle Sensor Basic Kit, an Arduino-compatible, all-in-one electromyography (EMG) sensor kit that provides you with the bare minim...

The MyoWare® 2.0 Muscle Sensor Development Kit is an Arduino-compatible, all-in-one electromyography (EMG) sensor kit that provides you with all th...

The MyoWare® 2.0 Power Shield is designed to easily power the [MyoWare 2.0 Muscle Sensor](https://www.sparkfun.com/products/18977) for remote appli...

The MyoWare® 2.0 Reference Cable is meant as an extension for the [MyoWare 2.0 Muscle Sensor\'s](https://www.sparkfun.com/products/18977) reference...

This is a 10 pack of the MyoWare® Reference 2.0 Cables. The MyoWare 2.0 Reference Cable is meant as an extension for the [MyoWare 2.0 Muscle Sensor...

The MyoWare Muscle Sensor is now designed to be wearable, allowing you to attach biomedical sensor pads directly to the board itself. However,...

The MyoWare LED Shield is designed to pair with the MyoWare Muscle Sensor. The blue 10-segment bar graph shows the magnitude of the measured signal...

Using our muscles to control things is the way that most of us are accustomed to doing it. We push buttons, pull levers, move joysticks… but what i...

Using our muscles to control things is the way that most of us are accustomed to doing it. We push buttons, pull levers, move joysticks…but wh...

The MyoWare Power Shield is designed to take two standard CR2032 coin cell batteries to power the MyoWare Muscle Sensor. We have made this board in...

This is the MyoWare Proto Shield, a simple proto-board for your MyoWare Muscle Sensor. With this shield you will be able to use the area provided t...

The NCP1402 is a 3.3V DC-DC converter. The breakout board will accept voltage inputs between 1 and 3 Volts (such as 1 or 2 AA batteries) and output...

Mini Pliers. These are great little pliers! A must have for any hobbyist or electrical engineer. Crucial for inserting devices into bread boards an...

This set of sewing needles is a must-have when stitching together your next e-textile project. Each envelope contains three 48mm, 1.23mm thick need...

This is the NeoPixel Stick from Adafruit, a small chainable board with eight 5050 WS2812 RGB LEDs. The WS2812s are each addressable as the driver c...

This is the SMD connector for the Nintendo DS touch screen.  4-pin right angle ZIF connector at 0.5 mm pitch. Documents: Datasheet

This a breakout board for the SMD connector for the Nintendo DS touch screen.  4-pin right angle ZIF connector at 0.5 mm pitch broken out to 4 0.1 ...

This non-invasive current sensor (also known as a "split core current transformer") can be clamped around the supply line of an electrical load to ...

This non-invasive current sensor (also known as a \"split core current transformer\") can be clamped around the supply line of an electrical load t...

Raytac’s MDBT50Q is a BT 5.2 stack (Bluetooth® low energy or BLE) module designed based on Nordic nRF52840 SoC solution, which incorporates: GPIO, ...

**Description**: These are standard nuts with 2-56 thread. For use with 2-56 machine screws and five button pad set listed below. Sold in singl...

We could talk about how the Zinc used in these nuts is only from the finest old-growth Zinc trees from across the globe and is hand picked only at ...