MAGENTO IMPORT

OverviewThe I2C and serial display driver provides easy operation of a standard 20 x 4 or 16 x 2 LCD Text display. It requires only a 5v power su...

This is a kit that provides you with a basic assortment of capacitors to start or continue your electronics tinkering. No more looking under your d...

This breakout board is the simplest way to create a project with a single "momentary" capacitive touch sensor. No microcontroller is required here ...

The GP2Y0A51SK0F is the shortest-range Sharp analog distance sensor we carry, featuring a detection range of 0.8″ to 6″ (2 cm to 15 cm). The short...

This is a breakout board for the SP3485 RS-485 transceiver IC, which will convert a UART serial stream to RS-485. The SP3485 is a half-duplex trans...

This tiny audio amplifier is based on the Texas Instruments TPA2005D1. Its efficient class-D operation means low heat and long battery life. It can...

  This connector cable interfaces UFL RF connectors to RP-SMA antennas. Use it to attach any standard RP-SMA 2.4GHz antenna to the DPAC 802.11 modu...

This is a 3-terminal microswitch two pack, each equipped with a 20mm offset lever actuator. These switches have a great ‘clicky’ sound to them with...

These small steppers are a great way to get things moving, especially when positioning and repeatability is a concern. This is a Bipolar motor. Fea...

It's your basic blue action button! This is a very useful, small, panel-mount momentary switch. It is a SPST N.O. with 1/4" threading.  This button...

The 3560 magnetic contact switch is nice and small and is designed for flush or countersink installations. The switch handles gaps of up to 3/4 i...

We've been using and selling Analog Devices' ADXL accelerometers for a good while now, and now we've found another great part in the series! The AD...

  These 10 segment bar graph LEDs have many uses. With a compact footprint, simple hookup, they are easy for prototyping or finished products. Esse...

  The TSL235R light-to-frequency converter outputs a square wave (50% duty cycle) with frequency directly proportional to light intensity (irradia...

This carrier board for ST’s VNH5019 motor driver IC operates from 5.5 to 24 V and can deliver a continuous 12 A (30 A peak). It works with 2.5 to ...

This tiny board is an easy way to use Toshiba’s TB6612FNG dual motor driver, which can independently control two bidirectional DC motors or one bip...

This super small mono amplifier is surprisingly powerful - able to deliver up to 2.5 Watts into 4-8 ohm impedance speakers. Inside the miniature ch...

Listen up! This set of two 2.8" x 1.2" speakers are the perfect addition to any audio project where you need 4 ohm impedance and 3W or less of powe...

Make your robot or CNC move on rails super fast with a linear bearing platform. The platform is 34mm x 30mm and has four holes tapped for M4 machin...

Female 6-pin DIN connector. Compatible with MIDI cables.

The seven band graphic equalizer IC is a CMOS chip that divides the audio spectrum into seven bands. 63Hz, 160Hz, 400Hz, 1kHz, 2.5kHz, 6.25kHz...

That new Raspberry Pi® computer you just got has a row of 2x13 pin headers soldered on - those are the GPIO (general purpose input/output) pins and...

This lovely little shield is the best way to add a small, colorful and bright display to any project. We took our popular 1.8" TFT breakout board a...

  FEATURES: USB to serial cable three wires for Breadboard connection SERIAL output 3.3V voltage levels GND=BLUE, RX(INPUT)=GREEN, TX(OUTPUT)=RED ...