MAGENTO IMPORT

These lightweight aluminum brackets make it easy to mount and integrate the Sharp GP2Y0A02, GP2Y0A21, and GP2Y0A41 Distance Sensors into your proje...

The Pololu Pushbutton Power Switches are sophisticated power control alternatives to bulky mechanical switches. The main function is pushbutton-ba...

This breakout board for TI’s DRV8880 microstepping bipolar stepper motor driver features adjustable current limiting, overcurrent and overtemperatu...

  Mounting bracket for EMG49 Gear motor. It is made with 2mm thick strong aluminum for EMG49. Blue enamel finish. This product is sold individually.

The TSA01 is a voltage output temperature sensor module employing Microchip's MCP9700A sensor. Specification     Operating Voltage    2.3v to ...

The ETH8020-B is a drop in update of the ETH8020 with additional upgrades. The ETH8020 provides 20 volt free contact relay outputs with a current r...

This kit has all the parts needed to connect to the Ethernet port on Teensy 4.1. This kit includes an Ethernet MagJack, bare circuit board, ribbon ...

Connect this to that without soldering using these mini alligator clip test leads. 15" cables with alligator clip on each end in six colors. Strong...

As an updated version of Grove - Light Sensor 1.0, the Grove - Light Sensor v1.2 is also aimed at measuring light levels, however with higher relia...

A prototyping board is one of the main steps in hardware development, also called a perf board. Breadboard, wiring and punching in chips, resistors...

This Relay Shield for Arduino acts like a switch. It is commonly used to control anything over 5V such as lamps, water pumps and garage doors.   On...

DHT22 capacitive humidity sensing digital temperature and humidity module is one that contains the compound has been calibrated digital signal outp...

The SparkFun Serial Basic Breakout is an easy-to-use USB-to-Serial adapter based on the CH340G IC from WCH. It works with 5V and 3.3V systems and s...

This is SparkFun Beefy 3 FTDI Basic Breakout for the FTDI FT231X USB to serial IC. The pinout of this board matches the FTDI cable to work with off...

Input voltage range: (9-36)VDC Fixed output voltage: 5V or 12V selectable Screw terminal and power jack for input Screw terminal, USB-A connecto...

This 2x20-pin strip, right-angle female header is a perfect companion piece to our 2x20-pin Dual Male Header.  It's a great way to add right-angle ...

ON...off...ON...off...ON...off...ON...off...WE CAN'T STOP CLICKING THIS ON-OFF SWITCH! It has such a satisfying click and it works so well.  Plus, ...

 XBee radios are an awesome way to add wireless capability to your Arduino project and now it’s even easier with the SparkFun XBee Shield. The shie...

With a slip ring assembly, your electronics can now twist and turn safely. Add wheel encoders, 360 degree sensors, rotating LEDs, rotors and more! ...

This disc load cell (sometimes called a strain gauge) can translate up to a whopping 200kg of pressure (force) into an electrical signal. Each load...

Running out of memory space in your Arduino project? The SparkFun microSD Shield equips your Arduino with mass-storage capability, so you can use i...

Bus Blaster v4 is an experimental, high-speed JTAG debugger from Dangerous Prototypes. Thanks to a reprogrammable buffer, a simple update over USB ...

Have you gazed longingly at large TFT displays - you know what I'm talking about here, 4", 5" or 7" TFTs with up to 800x480 pixels. Then you look a...

OpenCM9.04 is an open-source controller that runs under 32bit ARM Cortex-M3. The C version uses an exclusive 3PIN connector to control the ROBOTIS...