Sparkfun

This is a 50mm long ESLOV to ESLOV cable. The ESLOV connector has five pins (one more than standard I2C) for automatically configuring the module a...

The MyoWare® 2.0 Reference Cable is meant as an extension for the [MyoWare 2.0 Muscle Sensor\'s](https://www.sparkfun.com/products/18977) reference...

The SparkFun Qwiic Connect System is constantly growing in popularity with makers. So to make it even easier to get started, we\'ve assembled this...

This is a handy cable for connecting a six pin GHR-06V type locking connector to breadboard friendly male pins. The cable features a 1.25mm pitch ...

This is a basic RP-SMA (Reverse Polarity Sub-Miniature A) male to female connector cable. Each cable is 10M (393.7in.) long with RG58 housing. The ...

This is a 4 pack of wires that are pre-terminated with an alligator clip on one end and a pigtail hookup on the other. Alligator clips are a staple...

This is a basic SMA (Sub-Miniature A) male to female connector cable. Each cable is 25cm (9.8\") long and has a 50Ω impedance that can handle freq...

This servo cable has a shrouded male servo connector on one end, and 3x breadboard hookup pigtails at the other end. This makes it easy to connect ...

This is a servo adapter cable that allows you to hook up your servo directly to alligator clip connections. On one end you have a shrouded male se...

This is a jumper adapter cable that comes pre-terminated with a female Qwiic JST connector on one end and a breadboard hookup pigtail on the other....

This is a 100mm long 4-conductor cable with 1mm JST termination. It's designed to connect Qwiic enabled components together but can be used for ot...

With the SparkFun Qwiic Connect System expanding every day, we want to make sure it becomes as accessible as possible but we understand there are o...

The Raspberry Pi Zero and Zero W are both equipped with a smaller CSI (Camera Serial Interface) port than on a full-sized Raspberry Pi board --- lu...

Simple IDC ribbon cable. Used for AVR programming, general communication, and all around handy-ness. Datasheet shows an incorrect length. Cable...

This is a 10 pack of the MyoWare® Reference 2.0 Cables. The MyoWare 2.0 Reference Cable is meant as an extension for the [MyoWare 2.0 Muscle Sensor...

When experimenting with GPS or RF it can be very handy to have the antenna on the top of your house or car with a clear view of the sky while you ...

This is a 6-pin JST-ZHR connector terminated with breadboard compatible male pins. This is a handy cable for various sensors, radios and other devi...

This is a 4-pin JST-ZHR connector terminated with breadboard compatible male pins. This is a handy cable for various sensors, radios and other devi...

This is a handy cable for connecting a five pin GHR-05V type locking connector to breadboard friendly male pins. The cable features a 1.25mm pitch...

This is a basic RP-SMA (Reverse Polarity Sub-Miniature A) male to female connector cable. Each cable is 25cm (9.8in.) long with RG174 housing. The...

This is a basic RP-SMA (Reverse Polarity Sub-Miniature A) male to female connector cable. Each cable is 1M (39.3in.) long with RG174 housing. The ...

This is a basic SMA (Sub-Miniature A) male to female connector cable. Each cable is 1M (39.3in.) long with RG174 housing. The SMA connectors at eac...

This is a basic SMA (Sub-Miniature A) male to female connector cable. Each cable is 25cm (9.8in.) long with RG174 housing. The SMA connectors at e...

This is a 6-pin JST-ZHR connector terminated with breadboard compatible male pins. This is a handy cable for various sensors, radios and other dev...