Sparkfun

This is a PCB edge mount, SMA RF connector. These connectors are perfect for prototyping with the GPS and Cellular devices that require an antenna ...

A 433MHz antenna that uses an SMA connector and is 200mm long with a gain of 2dBi. Comes with the frequency laser printed on the antenna. **Fea...

Designed for 810-910 MHz (868MHz center frequency) this antenna is ideal for distant LoRa nodes. Uses an SMA connector and is 200mm long with a ga...

This is a 915MHz SMA Duck Antenna for use with the AHPI7292S WiFi HaLow HAT. We\'ve distinguished it as for use with this HAT as it\'s an SMA conn...

This RP-SMA to U.FL Cable is commonly used to attach WiFi, Bluetooth, or nRFxxx based devices to a 2.4GHz antenna. What makes this unassuming cabl...

This SMA to U.FL Cable is commonly used to attach WiFi, Bluetooth, or nRFxxx based devices to a 2.4GHz antenna. What makes this unassuming cable sp...

A U.FL to SMA (jack) bulkhead straight connector with a 1.32 mm diameter cable. Less than -2 dB cable insertion loss up to 6 GHz. Both connectors ...

This adhesive, dual band antenna is perfect for situations when you\'re trying to get a signal out from a transmitter that you\'ve jammed down int...

This small form-factor antenna offers a 2.4GHz frequency range. These antennas offer adhesive backing that simplifies mounting within the device fo...

This is a small 1/4 wave rubber duck antenna for (European band) LoRa or other 868MHz communication. Antenna has a center frequency of 868MHz and ...

The GW.17 Click–in Terminal Antenna is a high performance robust 2.4GHz dipole antenna designed for quick assembly onto finished products. The spec...

This ANT700 is a telescopic antenna designed for operation from 300 MHz to 1.1 GHz with a total length that is configurable from 9.5 cm to 24.5 cm...

This ANT500 is a telescopic antenna designed for operation from 75 MHz to 1 GHz with a total length that is configurable from 20 cm to 88 cm long....

This is an inner thread (outer nut) adapter that will connect to any of our wireless boards or interface cables and allow you to use an antenna/ca...

This is an adapter that converts an RP-SMA board to an SMA antenna. The adapter will connect to any of our 2.4GHz wireless boards ([Bluetooth](http...

This is a 4\" connector cable that interfaces U.FL RF connectors to regular SMA connectors. This cable is commonly used to connect larger GPS ante...

Itty-bitty U.FL SMD connector. Great for tight PCB layouts that require antenna connections. **Documents:** * [Datasheet](http://cdn.sparkfu...

900/1800 MHz Duck Antenna 2dBi with regular RP-SMA RF connector. Perfect for use with the XBee 900MHz units. 50 ohm impedance. 105mm long. Be s...

Commonly used to attach WiFi, Bluetooth, or nRFxxx based devices to a 2.4GHz antenna. **Features:** * 4\" Length **Documents:** * [Dat...

PCB edge mount - SMA RF connector. Perfect for prototyping with the GPS and Cellular devices that require an antenna connection. These connectors ...

PCB edge mount Reverse Polarized - SMA RF connector. Perfect for prototyping with our RF ICs. This is a standard edge connector. The thickness bet...

Need range? 2.4GHz Large Duck Antenna 5dBi with Reverse Polarized - SMA RF connector. Perfect for prototyping with our RF ICs. 50 ohm impedance. ...

2.4GHz Duck Antenna 2.2dBi with Reverse Polarized - SMA RF connector. Perfect for prototyping with our RF ICs. 50 ohm impedance. 4\" long. Not ...

2.4GHz ceramic chip antennas. Very small antennas that work nicely with the Nordic ICs. Don\'t expect these little guys to perform as well as thei...