Sparkfun

This panel mount USB-C extension cable enables you to more easily enclose a project that contains a USB-C port. The cable is 6" in length and incl...

This is a very simple 1m long Male RP-TNC to Male RP-SMA cable. We like to use this cable to connect our ultra high-frequency RFID antennas to an ...

This is a 4 pack of wires that are pre-terminated with an alligator clip on one end and a pigtail hookup on the other. Alligator clips are a staple...

Ribbon cable is really helpful in situations where you need to make a lot of connections without a big mess of wires. Nothing makes a project look...

This is an interface cable for the [Bus Pirate](http://www.sparkfun.com/commerce/product_info.php?products_id=9544), designed to connect to its 2x...

The SparkFun Analog MEMS Microphone Breakout makes it easy to work with the InvenSense ICS-40180 analog microphone. This board features an OpAmp t...

The SparkFun RV-8803 Real Time Clock Module is a Qwiic-enabled breakout board for the RV-8803 RTC. The RV-8803 boasts some impressive features incl...

The SparkFun Load Sensor Combinator is a bare PCB that combines four load sensors into a standard four-wire [Wheatstone bridge configuration](http:...

The CY7C65213 USB to UART serial breakout is designed to provide users with a means to access all available I/O pins on the IC, and to provide a 6...

Cherry MX Keyswitches are top-of-the-line mechanical keyboard switches. They're satisfyingly “clicky”, reliable up to tens-of-millions of key press...

This simple board breaks out a female USB type A connector\'s VCC, GND, D- and D+ pins to a 0.1\" pitch header. If you want to add a USB to your p...

The \'must have\' IC for TTL/CMOS projects finally has its own breakout board! This is the RS232 converter IC that is capable of running at 3V and...

This breakout for the Silicon Laboratories Si4703 FM tuner chip is a little more stripped down than our FM Tuner Evaluation Board. If your project...

This is a breakout board for the very handy 16-Channel Analog/Digital Multiplexer/Demultiplexer CD74HC4067. This chip is like a rotary switch - it...

6 pin SOT-23 to DIP adapter. Created to take SOT23 of various pin sizes breakout to DIP. This will work with 3-pin MOSFETs, BJTs, Voltage Regulato...

This is a PCB edge mount, SMA RF connector. These connectors are perfect for prototyping with the GPS and Cellular devices that require an antenna ...

This is an Extremely Efficient, Wide Band, Flexible LTE Antenna with a small footprint. This easy to install durable, flexible polymer antenna ope...

Raytac's MDBT50Q is a BT 5.2 stack (Bluetooth® low energy or BLE) module designed based on Nordic nRF52840 SoC solution, which incorporates: GPIO...

The BMD-34 series are advanced, highly flexible, ultralow-power multiprotocol modules that enable concurrent Bluetooth® 5, Thread and Zigbee (IEEE ...

The SparkFun IN100 NanoBeacon Board offers a 2.4 GHz wireless low-energy BT beacon breakout with exceptionally low power consumption features and m...

A 433MHz antenna that uses an SMA connector and is 200mm long with a gain of 2dBi. Comes with the frequency laser printed on the antenna. **Fea...

Designed for 810-910 MHz (868MHz center frequency) this antenna is ideal for distant LoRa nodes. Uses an SMA connector and is 200mm long with a ga...

The SparkFun NINA-B306 Thing Plus offers a unique combination development platform in the Thing Plus form factor featuring the NINA-B306 from u-bl...

The SparkFun Notecarrier Cellular Function Board adds a cellular modem to the MicroMod ecosystem using the Notecard - NOTE-NBGL-500 from [Blues Wir...